The Bullet pumps are ideal for dewatering constructions sites, mines, circulating fountain water, or for all around use in industrial plants and utilities.
TOP DISCHARGE AND PERFORMANCE
The Silver Bullet pumps (0.5HP) are ideal for dewatering construction sites, mines, circulating fountain water, or for all around use in industrial plants and utilities.
Recommended accessories
Piggy Back type float switch (115 Volt w/ plug):
- 30’ Cable, 115 Volt = BJM Item # 201050
- 50’ Cable, 115 Volt = BJM Item # 201060
Side Mount Vertical Rod Type Float Switch:
- 30’ Cable, 115 Volt = BJM Item # 201051
Built-In Switch (Permanently attached to pump):
- 33’ Cable (115 or 230 Volt) = BJM Item # 201724
- 50’ Cable (115 or 230 Volt) = BJM Item # 201725
Manual Starter Box:
- Manual On/Off starter box for R400-115 = BJM Item # 201109
Auto Starter Box:
- Auto On/Off starter box for R400-115 = BJM Item # 201110
Simplex Control Panel - (3 mechanical float switches):
- Single Phase Control Panel for R400-115 = BJM Item # 201069
- Single Phase Control Panel for R400-230 = BJM Item # 201066
Duplex Control Panel - (4 mechanical float switches):
- Single Phase Control Panel for R400-115 = BJM Item # 201074
- Single Phase Control Panel for R400-230 = BJM Item # 201071
Interested in this item or want more information?
Hours:
Phone: 800-613-3873
Email: info@aaatool.net
Can't find what you want? Give us a call and we can help you find it.
Details
GENERAL DATA
Max. Flow: Gpm: 66
Max. Head: Ft: 35'
Pump Type: Top Discharge, Dewatering
Strainer Opening: 0.1875"
Discharge Size: 2" NPT-M
Max. Submerged Depth: 200'
Shipping Weightibs: 33
CONSTRUCTION/MATERIAL DATA
Motor Casing: 304SS
Pump Volute: Cast Iron
Impeller - Multi Vane: Cast Iron
Lip Seals &0-Rings: Buna-N
Rotor Shaft: 304 SS
External Hardware: 304 SS
Oty. Oil In Seal Chamber: 1.35 U.S. FLOZ.
ELECTRICAL/MOTOR DATA
Motor Rating: Hp: 0.5
Motor Rpm: 3450
Motor Insulation Cuss: F
Motor Service Factor: 1.1
Voltage: 115/230,1PH-60HZ
Current F.La: 3.8
Motor Protection: Thermal Breaker
Power Cord: Gage; Length: A.W.G. 16/3; 33', STOW
Maximum Liquid Temperature: 104° F
Seal Minder: Not Available
The Bullet pumps are ideal for dewatering constructions sites, mines, circulating fountain water, or for all around use in industrial plants and utilities.
Top Discharge – allows for superior cooling of motor and provides a slim line design.
Longer Power Cord – Standard 33ft. power cord on pumps ½ HP and below and 50ft. on pumps 1HP and above.
304SS Motor Housing – Superior abrasion resistance will not wear out like aluminum motor housings when pumping sandy water.
Three Seal Motor Protection - Motor is protected by double mechanical seals. Lower seal made of silicon carbide/silicon carbide and upper seal is made of carbon/ceramic*. An additional lip seal has been installed above the impeller, to help prevent abrasives such as dirt, silt or sand, from entering into the seal chamber.
More Motor Protection – Winding protection and (NEMA) Class F motor insulation allows motor temperature to raise to 230°F, superior to pumps with Class A and B insulation. Automatic switch turns pump motor off if temperature and/or amp draw raises too high. When the motor cools the switch will automatically reset and the pump will turn back on.
Tough Pump Construction – Hardened cast iron stands up to rough handling and pumping sandy water unlike pumps with soft resin impellers or plastic exterior components*.
R400D Special Feature – The mode Up Pumps, will pump down to 1/12 th of an inch. It features a special diaphragm value that prevents water backflow.
Additional Information
Manufacturer: BJM Pumps, LLC
For More Information on the R400-230 Top Discharge Dewatering Pumps,
[Click Here] to Link to Manufacturer Web Site